Gunville Gun PartsGunville Gun Stocks Custom madeGunville.com walnut gun stocks
gunville gun stocks homeCustom Gun StocksMilitary Repro Woodgunville gun partscollectible gun books out of printgun stock wood gradinggunville gun parts about us and servicesgunville gun stocks silver hill holding co

Services

We offer fitting finishing services on your gun / gun stock for a reasonable price. Each job/gun is an individual so email us for a quote. You can start with fit to your reciever, and buttplate and sand ready for you to finish. Or, we can turnkey the job--fit, finish, and checker.

We also do small stock jobs such as repairs and install recoil pads and buttplates or grip caps. In addition we refinish, rechecker and glassbed.

Please contact us for more information on any of our services.

We pride ourselves in our work and our quality of customer service.

  • gun stock production
  • custom stock production
  • wood selection and drying
  • raw materials
About Us

We have been in the gun business, gun parts business and gun stock business since the early 70’s. Our major business since approximately 1985 has been selling reproduction gun stocks. At first, we resold stocks made by a local provider. As we sold more stocks, we began cutting and handling our own walnut blanks so as to keep a better handle on the stocks our supplier was making. This developed into our seeking out more sources of walnut and we began to buy “yard trees” and a lot of trees that were large enough to use, but were unsalable. The lumber mills simply don’t buy trees with limbs, knots, wire, nails ect. And a lot of really good walnut was going to waste. Much of it got thrown into a landfill, rotted where it fell, or, was made into firewood, etc. We heat our shops with wood, so no part of the tree is wasted. To be useable for gunstock purposes a tree has to be approximately 20" diameter or better mainly because a minimum board thickness is around 2-3/4" when green. The best feather crotch fancy wood comes from where large limbs grow out from the main trunk. This is also where the hardest, most dense, wood comes from. When sawed, we always coat the fancy areas with anchor seal which slows drying and reduces the chance of cracking, checking, and other blemishes.

I have heard for many years the stump myth. I have heard for years this is the best of the best for gun stocks. Tain’t so! True, the stump wood does have real nice burly figure but------it is usually real pourus and very light. If you go below a few inches underground, this is what you run into. On some very large stumps there are sometimes some wavy figure in the large roots and if you don’t go too far it is useable. Get much below the ground line and it gets porous fast. Also, in these areas are many holes and defects, and plenty of rocks and dirt.. from just below the ground line up a couple of feet there is usually some very good walnut and usually shows a lot of fiddleback. Sometimes you get feather crotch too. 80% of what we sell is standard straight grained lumber. The other falls into, semi-fancy, A grade. AA grade, AAA grade, and exposition. The final grade is in the eye of the grader and if you don’t like what you got, we’ll replace it or negotiate.

Back to our making gunstocks. After many years of buyiing from another dealer; we purchased some terrco. Duplicating machines and began producing our own. For years I heard people complaining about too much extra wood being left on the product. Don’t get me wrong, when you fit a reproduction stock, you have to have some wood to work with to fit and sand. The reason for this is all guns are individuals and not all fit the same. We feel we have cut it to a minimum and leave enough to sand and finish. After the stocks are made; we fit all of them to an original reciever and leave the tangs(if present) snug. Then we mark around the metal and sand it to approximately a dime or nickel thickness with 220 grit. This is about the minimum extra wood you need to start with. If you don’t like the product, send it back.

I mentioned the terrco carving machines and these are hand operated duplicators. The same machines were used in all the older furnitue opeartions and allow a “feel” of the wood as you work with it. My operators are all experienced woodworkers and gunsmiths and they do excellent work. I will put these guys and their work up against any CNC product available--guaranteed!!

We also offer a fitting service for your gun. We can do anything from fit and sand the stock to your gun up through a turnkey job - complete fit, finish and checker.

If you have questions, email me or call anytime: (336) 425-3888

 



custom mauser gun stock patterns
We have devloped many Sporter patterns for Mausers including a few original Oberndort patterns.

>> CLICK HERE
mauser stock patterns

See our Video Presentation

Click here to view our Frequently Asked Questions from the experts themselves.

>> CLICK HERE

HOME | GUN STOCKS | MILITARY REPRO WOOD | GUN PARTS | COLLECTIBLE GUN BOOKS | WOOD GRADING | MAUSER STOCK PATTERNS | SERVICES | SOLAR RESOURCES | FAQ | TESTIMONIALS | CONTACT US
© 2004-2009 Gunville. All Rights Reserved.